Oct 29, 2020 Windows should download the correct drivers as soon as you connect the cable to the computer. Crippledchicken Member. Premium Subscriber. Joined Dec 28, 2004 Messages 564.
- Step 2: Run the detect drivers scan to see available updates. Step 3: Choose which driver updates to install. Drivers and Downloads FAQs. Find out more information on why you should update your drivers, how to update them, installation videos, and where to find the drivers you need.
- Cable and Adapter Drivers Information. Some Intel ® products require drivers. You must set up the correct drivers before using those products. For example, to use an Intel download cable or programming unit to program devices with the Intel Quartus ® Prime software, you must first set up the correct driver.
- Select the category your product is in. 40348 Help.zip; 40348 Software.zip; Audio Video Devices. 29358 Firmware.zip; 40697 Software.zip.
- Cables with FTDI chipset (FT232R) will automatically download the correct driver when inserted into the USB port. Drivers for the WCH chipset (CH340/341) should also download automatically. If not, the driver and procedure can be found at this Link.
Cable Drivers
MD-CC3/4 and Windows x64 systems
The older versions of the MD-CC30x-001 USB to SPI and MD-CC40x-001 USB to RS-422/485 communication converter cables were developed to work with Windows 32-bit operating systems. These cables must have the the internal ID reset in order to be supported by current Windows 64-bit operating systems.
How do I know if I have an older cable?
The most recent cable will install as 'Silicon Labs C210x USB to UART Bridge (COMXX)' in the device manager of your PC under Ports (COM and LPT).
In the case of MD-CC3 and MD-CC4 cables with the incompatible ID, when the device manager attempts to find the drivers and fails to install them, the message that opens will show the IMS part number: MD-CC400-000 or MD-CC300-000 on the dialog, as shown below.
Additionally, the part number will display under other devices in your computer's device manager.
Please contact applications for information on cable updates
MD-CC404-000 & MD-CC405-000
The MD-CC404/5-000 drivers are applicable to Lexium MDrive RS-422/485 products. This device is 'plug-n-play' and the drivers should automatically install to an Internet connected PC. Should your network block automated driver installs or the PC not be connected, the drivers may be downloaded from:
MD-CC404-000 Drivers (FTDI VCP Drivers)
Note: This link will open in a new browser tab/window.
Drivers Cable Rs232
MD-CC40x-001
The MD-CC40x-001 drivers are applicable to MDrivePlus and MForce Motion Control RS-422/485 products. This device is 'plug-n-play' and the drivers should automatically install to an Internet connected PC. Should your network block automated driver installs or the PC not be connected, the drivers may be downloaded from:
MD-CC40x-000 Drivers (Silicon Labs CP210x USB to UART Bridge VCP)
Note: This link will open in a new browser tab/window.
Legacy MD-CC40x-001 drivers
Use ONLY with CC4 cables with the IMS ID on 32 bit Windows systems
Driver Package | Installation Instructions
MD-CC30x-001
The MD-CC30x-001 drivers are applicable to MDrivePlus and MForce Step/direction and Speed Control SPI products. This device is 'plug-n-play' and the drivers should automatically install to an Internet connected PC. Should your network block automated driver installs or the PC not be connected, the drivers may be downloaded from:
MD-CC30x-001 Drivers (Silicon Labs CP210x USB to UART Bridge VCP)
Note: This link will open in a new browser tab/window.
Legacy MD-CC30x-001 drivers
Use ONLY with CC3 cables with the IMS ID on 32 bit Windows systems
Driver Package | Installation Instructions
MD-CC50x-000
These drivers apply to the MD-CC500-000 (MDrivePlus and MForce products) and MD-CC501-000 (Lexium MDrive products) USB to CANopen Communications converters
MD-CC50x-000 Drivers (PEAK Systems PCAN-USB)
Note: This link will open in a new browser tab/window.
If your cheap BMW INPA K+DCAN USB interface with FTDI chip failed to install drivers or the system prompt cannot locate the drivers. Here is a little write-up on how to fix it.
Disclaimer:
I am using Windows 8.1 system. No sure if it works on yours. You are on your own risk.
Pre-installation caution:
Here are the INPA driver & software, free download links. If the driver/software is working, then ignore the next part. Otherwise take a look at the following part for reference.
INPA Driver: http://www.obd2vip.com/download/inpa-driver.zip（Close antivirus software or set your browser to download success）
INPA software: http://www.obd2vip.com/download/inpa-2.zip
Procedure:
1. Open your Device Manager. Control Panel–Hardware & Sound–Device Manager.
2. Connect the INPA K+DCAN cable with computer/PC-Double click
3. Locate USB Serial Converter->DetailsDropdown Menu->Hardware IDs. The PID number is the one you want. Will most likely be 0000.
4. Download CDM v2.08.30
http://www.ftdichip.com/Drivers/CDM/CDM%20v2.08.30%20for%20Windows%208.1.zip
5. Disable “Driver signature verification” Settings–Change PC Settings–Recovery–Advanced Startup–Restart.
This will restart your PC to Advanced settings. From there: Troubleshoot–Advanced Options–Startup Settings–Restart–F7
Follow these picture guides:
Your PC will then restart with signature verification disabled. You are now able to edit the INPA drivers.
6. Unzip the Drivers file that you just downloaded and open up
7. Open ftdibus.inf
8. Replace every PID_6001 with PID_0000 to match your hardware ID. Scan through the whole document. Then save it.
9. Then find ftdiport.inf. Do the same to ftdiport.inf
10. Back in your Device Manager double click on your OBDII cable again.
Locate USB Serial Convertor Properties->Driver->Update Driver-> Browse my computer.
Locate your driver and install. You will need to install it for both USB Serial Converter and Ports & COM.
Drivers Cable Usb
11. Setup INPA cable as normal and run INPA software.
It seems that the white FTDI chip INPA cables have to be manually put into D-CAN mode. This file will take care of that. It is normal for the LED to go out.
http://www.mediafire.com/download/35fnrnd3q3dvf3w/D-CAN.exe
If you put the cable into DCAN mode, the LED goes off, and it says there is no adapter connected. Please connect it to the car and run the DCAN mode.
Baofeng Cable Drivers
Who Viewed This Article Also Views: